Posted on

Allison 3000 & 4000 Gen5 Turbine Shaft Speed Sensor Circuit P0715 Solution

Allison 3000 & 4000 Gen 5

This instruction show you steps on how to solve Allison 3000 & 4000 Gen5 transmission turbine shaft speed sensor circuit P0715.

 

Allison 3000 & 4000 Gen 5

Related Contents:

Allison DOC GEN5 Diagnostic Software 2024.07

2023 Diesel Repair Desktop DTC Solutions V2.9.98+ Diesel Explorer

 

 

DIAGNOSTIC RESPONSE:

DNS, Lock in current range

 

CIRCUIT DESCRIPTION:

The speed sensors are devices which convert mechanical motion to an electrical signal. This test detects a turbine speed sensor circuit short to battery, ground, or open.

 

ACTION TAKEN WHEN THE DTC SETS:

When DTC P0715 is active, the following conditions occur:

1 If the DTC sets while shift not in process, remains in current range.

2 If the DTC sets while shift is in process, complete shift and lock in that range.

3 There is no response to shift selector requests.

4 DTC is stored in TCM history.

5 The CHECK TRANS light illuminates.

6 The TCM inhibits TCC engagement.

7 The TCM freezes shift adapts.

 

CONDITIONS FOR CLEARING THE DTC:

Use the diagnostic tool to clear the DTC from the TCM history.The TCM automatically clears the DTC from the TCM history if the vehicle completes 40 warm-up cycles without the DTC recurring.

 

DIAGNOSTIC AIDS:

DTC P0715 may be caused by:

1 W120 and/or W180 shorted to another wire in chassis harness or to ground.

2 W120 and/or W180 high resistance or open circuit.

3 Broken or defective connector assemblies allowing pushed back pins to short together.

4 Unlocked connectors, missing seal plugs allowing moisture in connectors.

5 Fatigued wires at speed sensor connectors (broken strands).

6 Incorrect pin crimps or expanded terminals.

7 Defective turbine shaft speed sensor.

8Defective TCM.

9 Damaged rotating clutch drum.

10 Wire pair not twisted or not sufficiently twisted.

 

NOTE:Confirm that the speed sensor wiring consists of twisted pairs at the rate of 12 to 16 twists per 300 mm. These twists must extend the entire length of the wiring harness to within at least 50 mm of the speed sensor connector.

 

NOTE: The OEM Transmission warranty, or the extended coverage for parts and labor, does not cover transmission or vehicle damage caused by drivelines that do not meet the OEM Transmission specifications.

Posted on

Allison 3000 & 4000 Gen5 Transmission P0602 TCM Not Programmed Solution

Allison 3000 & 4000 Gen 5

Here is the solution for Allison 3000 & 4000 Gen5 Transmission P0602 trouble code TCM not programmed error.

Allison 3000 & 4000 Gen 5

Related Contents:

2023 Diesel Repair Desktop DTC Solutions V2.9.98+ Diesel Explorer

 

DIAGNOSTIC RESPONSE:

Lock in Neutral

 

CIRCUIT DESCRIPTION:

This test verifies VEPS calibration within TCM is valid.

 

ACTION TAKEN WHEN THE DTC SETS:

  1. The CHECK TRANS light Iluminates.
  2. DTC is stored in the TCM history.
  3. The TCM inhibits shifts to range.

 

CONDITIONS FOR CLEARING THE DTC:

TCM must be recalibrated.

 

DIAGNOSTIC AIDS:

Indication of invalid VEPS calibration include:

1 Not able to connect to TCM with the diagnostic tool.

2 Cat-eyes in shift selector windows.

3 Blank selector windows occurs after pressing any selector button.

4 Check that the TCM is getting battery power, battery grounds, and ignition sense signal.

Review applicable information in the OEM Technician’s Library, CONTROL SYSTEM AND TRANSMISSION SPECIFICATIONS. GENERAL TROUBLESHOOTING OF PERFORMANCE COMPL AINTS- SHIFT SELECTOR ISSUES, and other related information.