autoepccatalog, Author at Auto Machine Diagnosis EPC Download Installation Service

Posted on May 11, 2024May 9, 2024 by autoepccatalog

How Install Intermediate Drive Shaft for CLAAS Lexion 480

How to install Intermediate drive shaft for CLAAS Lexion 480 Combine.

Related Contents:

Steps:

1.Slide the intermediate drive shaft (1) into the feed rake housing from the left.
2.Slide on the lock collar bearing (2) and both sheet-metal flanges (3) on the left and bolt them down.
3.Align the shaft axially. Adjust the dimension (X) from the end of the shaft to the feed rake conveyor as follows:
LEXION 480 = 252 mm

4.Slide on the lock collar bearing (2) and both sheet-metal flanges (3) on the right and bolt them down.
5.Slide the gear on the shaft and align the shaft so that both gears are aligned.
6.Slide on the lock collars (4) on the left- and right-hand side and tighten by hitting in direction of rotation, then insert the set screw.
7On the left-hand side, place the parallel key in position, slide the V-belt pulley into place and tighten the clamping hub with the M 12 x 85 hex. bolt.

8.On the right-hand side, remove the gear and bolt down the bracket using the bolts that secure the sheet-metal flanges.
Then fasten the gear with the circlip and now bolt down the cover to the bracket with the M 6 x 12
hex. bolts.
9.Bolt down the hydraulic cylinder to the supporting arm using the M 8 x 65 and M 12 x 25 hex. Bolts and the eccentric bolts. Assemble the eccentric bolt so that there is still some free movement.

10.Adjusting the hydraulic cylinder:
– Press the drive motor down into the gear.
– Pull out the ram.
– Set and lock setting screw (S) so there is 0.5 mm of play
(1/4 turns) up to the stop.
11Install the cutterbar drive belt (P) and adjust it
– see page 7.2.2, Installing and adjusting the cutterbar drive belt (1) (Cutterbar drive without variable-speed drive) and/or Installing and adjusting the cutterbar drive belt (2) (Cutterbar drive with variable-speed drive).
12Install the left-hand guard and the universal coupling.

Posted on May 6, 2024 by autoepccatalog

Bobcat Engine P2B8C/P2B8D DEF Pump Motor Internal Duty Low/High

1) Overview

U004375-24

1 Electric problem (Supply module connector)
2 Electric problem (Wiring harness DCU to supply module, Supply module)
3 Electric problem (DCU connector, DCU)

Related Contents:

Service Analyzer 91.15 for Bobcat Diagnostic Software

2023 Bobcat Engine Analyzer ECU DCU Diagnostic Software

2) Component Location

3) Condition for Running Diagnostic
When pump motor is normal
4) Condition for Setting the Fault Code
When the sensor value (raw duty cycle) is less than 4%
5) Condition for Clearing the Fault Code
When the sensor value (raw duty cycle) is greater than 4%
6) Check List

Step	Inspection	Standard Value	YES	NO
1	P2B8C/P2B8D is occurred on diagnostic tool?	Step 2
2	After let the machine be in safety area and turn off the key switch	Step 3
3	Check sensor connection Connection problem?	Do necessary repair	Step 4
4	Check DCU connection Connection problem?	Do necessary repair	Step 5
5	Check the DCU voltage related pin connection and harness. Pin or connection problem?	Do necessary repair	Step 6
6	Check continuity and electrical insulation Electrical problem?	Fix harness	Change SM

Posted on May 1, 2024April 26, 2024 by autoepccatalog

Deutz TIRE4 Engine SCR Service Routines by SerDia2010

1 Pressure test
While pressure test with a stopped engine the DEF pump is regulated at 9 bar. The test is
used to check the pump components to their function. The test involves no automatic
evaluation and must be actively terminated. It is to verify that the system controls on 9 bar
and this pressure is retain.

2023 Deutz Serdia2010

Deutz Diagnostic Kit

2 Injection Test
At the start of injection testing first the DEF pressure is built up. Then a definite amount
DEF is injected. The test is used to check both, the pump module and the function of the
dosing module.
The dosing module must be removed for this test.

3 The service “empty lines” must be accomplished after a service routine is completed, that the DEF lines can be emptied after ignition change.
(This is not necessary for the EOL-test or the service regeneration)

SCR-Heater relay activate
Setting of the individual heating relay to check the customer’s wiring.
– DEF Heater Main-relay
– DEF Heater Suction line
– DEF Heater Pressure line
– DEF Heater Back flow
– electrical heater – Supply Modul
– tank heater relays (coolant water)

After changing the SCR Catalyst the service “SCR Cat changed” must be set.

inducement counter reset
The exhaust legislature requires that emission-related defects, provided they bear a
permanently,enable a power reduction.
Current derating must be reset after repairing/troubleshooting by the service tool.
The button appears only in Serdia2010 when the power reduction is active.
After the counter has been reset, the button disappears.

Posted on April 26, 2024 by autoepccatalog

Scania Truck Alarm System Wake-up Signal Short-circuit Solution

Here is the instruction show you guide on how to solve Scania truck Alarm system Wake-up signal short-circuit to ground.

Preparations:

Scania SDP3 2.60.1 Truck Diagnostic Software

Scania Multi EPC 2024.03

Scania VCI3 High quality

Wake-up signal for Scania Communicator, short circuit

Error identification

Wake-up signal for Scania Communicator is short-circuited to ground.

Cause

Fault in harness-to-component connectors or cable harness for the wake-up signal for Scania Communicator.

Internal fault in ALM control unit E7.

Notes

–

Symptom

The alarm system cannot initiate Scania Communicator.

Action

Disconnect the harness-to-component connector to ALM control unit pin A5.

Measure for short circuits throughout the cable harness.

If there are a number of harness-to-component connectors between the wake-up signal and the ALM control unit, disconnect them and measure in order to isolate the fault.

If the fault is not in the cable harness it is probably an internal fault in ALM control unit E7.

Posted on April 19, 2024 by autoepccatalog

Volvo MACK EPA07 Engine Flow Test Injector Activation by JPRO

Aftertreatment Injector Activation for Flow Test is supported on:
✓ Mack and Volvo EPA 07 engines.

Related Contents:

JPRO Noregon Commercial Fleet Diagnostics 2024

Noregon JPRO DLA+ 2.0 Adapter

The Aftertreatment Injector Activation for Flow Test activates the injectors to test flow.
1 Select Aftertreatment Injector Activation for Flow Test and press Enter or the Start button.

2 The test dialog will be displayed.

3 Select the Start button to begin the test.
4 Activation of the aftertreatment injector should result in a “click” sound. Monitor the displayed data values.
5 Select the Stop button to stop the test.
NOTE: To prevent damage to the engine, the test will automatically stop after 30 seconds.
6 When the test has completed, click the Exit button to return to the test selection dialog.

Posted on April 13, 2024April 8, 2024 by autoepccatalog

HINO J05E Engine 2018 VNT Actuator Initialize Error P003A Solution

This instruction show you guide on how to solve HINO J05E Engine 2018 VNT Actuator Initialize failure.

Related Contents:

HINO DX3 Diagnostic Software

NEXIQ USB LINK2

Technical Description:

1) The VNT actuator moves the nozzle vane steplessly by the LEA (Linear Electric Actuator) to control the turbo speed and boost pressure.

2) The LEA has a sensor to detect the movement of the actuator, always monitoring the reading and actual value of the nozzle vane opening.

3) Wiping operation is performed while the engine is stopped for the purpose of removing soot and oil coming out from the range of vane operation and checking the turbo mechanical operating range for abnormality.

DTC Set Condition:

1) DTC Detection Condition:

a) Starter key “ON”.
b) The battery voltage is in the range of 10 to 16 V.
c) The engine is stopped, or the engine speed remains at 500 r/min or more for 5 seconds or more.

2) Judgement Criteria:

a) Initialization failure – When the amount of operation after power has been turned ON is larger than HI range, or when the Hall IC output does not become constant after 5 seconds has elapsed

Reset Condition:

1) After normal operation is restored and the starter key is turned “LOCK”.

Indication, Warning or System Control Regulation When The DTC Is Set:

1) MIL: ON

2) SVS light: OFF

3) Engine output is restricted.

Symptoms On The Vehicle The DTC Is Set:

1) Symptoms On The Vehicle Due To Backup Control (Fail Safe Function):

a) Engine output is insufficient.

2) Symptoms On The Vehicle Due To Malfunction:

a) None

Pre-Inspection Work:

1) Check that the battery voltage is in the normal range.

After-Inspection Work:

1) Clear all past DTCs.

2) Check that no DTC is detected after test drive.

Possible Causes:

1) VNT link is stuck or cannot operate due to rust, etc.

2) External link is disconnected.

Posted on April 8, 2024 by autoepccatalog

Volvo All Engine Actuator Supply Voltage “A” P065713 Solution

The following components are connected to a common 12V supply

1) A138: DEF Direction valve

2) A138: Aftertreatment Diesel Exhaust Fluid (DEF) Pump Motor

3) Y81: Aftertreatment Diesel Exhaust Fluid (DEF) Tank Heater Valve

If an abnormal voltage or current is detected on the common supply a DTC is set

Volvo All Engine Actuator Supply Voltage “A” P065713 Solution

Related Contents:

[03.2024] Volvo Techtool PTT 2.8.241+ACPI 0.7.1.0 High Level+Devtool

Volvo Vocom

Volvo PROSIS 2024

Conditions for diagnostic trouble code (DTC):

1) Open circuit

Observable symptoms

1) None

Probable cause

1) Wiring harness

2) Connector

3)A138: DEF Direction valve

4) A138: Aftertreatment Diesel Exhaust Fluid(DEF) Pump Motor

5) Y81: Aftertreatment Diesel Exhaust Fluid(DEF) Tank Heater Valve

6)A137: Aftertreatment Control Module (ACM)

Posted on April 3, 2024 by autoepccatalog

How to Use SerDia2010 Perform EGR Actuator Test for Deutz Engine

This instruction show you guide on how to use SerDia2010 diagnostic to do EGR actuator test for Deutz engine.

Preparations:

2023 Deutz Serdia2010 v14.1.9.1 Diagnostic Software Free Download

Deutz Diagnostic Kit DECOM for Deutz Engine

Procedures:

The Button does not appear with The software P_802_680_640_005.

This test is designed for the if the EGR actuator motor has been replaced, the end position of the EGR actuator easy and simple
can be calibrated and stored in the ECU.
To run the EGR actuator reset open the corresponding use case in SerDia2010 as shown in the lower Image.

Once the Use-Case has started the test can be started directly by clicking on the
Button “EGR actuator reset” (pictured purple highlighted).

If the EGR reset is active, next to the selected button (in the lower purple marks) a
rotating icon appear.

If the EGR controller reset was successful, SerDia shows the message below.

Notice:This function is available at Competence Class 2.

Posted on March 30, 2024March 20, 2024 by autoepccatalog

CASE IH 20 Series Combine Bleeding Service Break Operation

CASE IH agriculture 7120-9120 series axial-flow combine bleeding service break operation guide.

The European machines may be equipped with a pressure limiting valve to prevent the main drive wheels from locking up. The valve incorporates a solenoid L-32 that when activated will expose the brake pressure lines to a relief.

Related Contents:

CNH DPA5 Diagnostic Kit

CNH EST 9.10 Diagnostic Software

CNH eTimGo Repair Manuals

Any time the brake is disassembled or lines removed, the system will require bleeding. To bleed the system proceed as follows:

REMEMBER: As the brake pedal must be depressed several times while bleeding,this job has to be done with two persons.

Procedures:

1 Park the combine on level ground and block the wheels adequately to prevent the combine form rolling. The engine does NOT need to be running.
2 Raise the header and engage the header safety latch. Stop the engine.
3 Verify that the brake reservoir is filled.
4 Slide a transparent hose over the RH outside bleed screw to catch the oil when bleeding.
5 Cab Operator holds down the LH brake pedal and pumps RH brake pedal.
6 Bleed Operator loosens RH outside caliper bleed valve (#1 in photo) to allow the air to bleed out, and then retightens it when oil comes out of the port.
7 Operator then loosens RH inside caliper bleed valve (#2 in photo) to allow the air to bleed out, and then retightens it when oil comes out of the port.
8 Operator in cab then holds down RH brake pedal and pumps LH brake pedal.
9 Repeat steps 5-7 for the LH side.
10 Check for the reservoir for proper oil level

Posted on March 25, 2024March 20, 2024 by autoepccatalog

Caterpillar C9 Engine PTO Engine Shutdown Switch Voltage Low

Caterpillar C9 engine PID 186-4 PTO engine shutdown switch voltage low solution.

Caterpillar C9 Engine

Caterpillar CAT ET 2023C

CAT Comm Adapter 3

A short to ground exists in the wiring for the PTO engine shutdown switch. The parameter “PTO Engine Shutdown Switch” must be programmed to “J1/P1:7” or “J1/P1:23”.

If the vehicle speed is not equal to zero, or if there are active vehicle speed faults, the engine will go to low idle. The engine will not shut down when the vehicle speed falls to zero. When the PTO engine shutdown switch is pressed, a 186-14 will become active. The code will stay active until the engine shuts down. When the engine shuts down, the code will be loggged.

Possible Causes:

1) ECM Connection/Harness

2) PTO Shutdown Switch Failure

3) ECM Failure

4) Wiring between PTO shutdown switch and ECM